+86 152 6187 8920Get Quote

How Nitrile Gloves Are Made: From NBR Latex to Packed Carton

Written by

in

Every argument a buyer ever has about a nitrile glove traces back to one of nine stages on the dipping line, and most of them to three: the compound, the leaching time and the finish. Knowing which stage owns which defect is what turns a complaint into a corrective action instead of a credit note.

This is our own process, written the way we would walk a buyer through it on the line at Taishan.

The plant behind the process

Our plant sits in Dajiang, Taishan, Guangdong, built in 2018 on a 74,000 m² site, with the first phase at around 27,000 m² covering the dipping lines and the water treatment plant, a research and development centre of roughly 800 m², and around 2,000 m² of clean room. It operates under its own ISO 13485 quality management system certificate. We supply nitrile gloves and clear vinyl gloves; we do not run a latex line and we do not make surgical gloves, so any reference to latex below is a process comparison, not a product offer.

The nine stages, and what each one owns

# Stage What happens The spec line it owns
1 Compounding NBR latex is blended with curing agents, activators, stabilisers and pigment, then matured under controlled agitation Tensile strength, elongation, colour consistency, and whether the glove is accelerator-free
2 Former cleaning Ceramic formers run through acid and alkali baths and brushes before every pass Surface defects, pinholes carried over from the previous cycle, cosmetic blemishes
3 Coagulant dip Heated formers enter a calcium nitrate coagulant bath; the pickup sets how much latex will deposit Gram weight and its distribution between cuff, palm and finger
4 Latex dip The former passes through the compounded NBR; dwell time and solids content set the film Thickness at each measurement point, and the weight tolerance per size
5 Pre-leach Hot water rinses soluble residues out of the wet film Residual chemicals, odour, and skin comfort complaints that surface weeks later
6 Beading Rollers turn the cuff edge into a bead Donning strength and cuff tears, the most common failure point in use
7 Curing The film is vulcanised through staged ovens Force at break, elongation, and ageing performance
8 Post-leach and finish A second leach, then either chlorination or a polymer coating, then stripping and tumble drying Donning, grip, tack, residual powder and colour shade
9 Inspection and packing Sampling, water leak and dimensional testing, boxing and carton packing AQL performance, count accuracy, lot traceability

Compounding: where the cost and the character are set

The compound is where a cheaper glove gets cheaper, and it rarely shows on a specification sheet. Three levers sit here. Pigment load changes nothing structural but changes colour consistency between lots, which is why a buyer who switches supplier mid-range sees two shades of blue on one shelf. The curing system — accelerators and activators — sets both cure speed and the residual chemistry that drives skin complaints. And the filler level is the quiet one: more filler means less NBR at the same gram weight, so two gloves can weigh the same and break at different forces.

That is the argument for buying against force at break rather than against grams alone. Our 3.5 g specification carries a force at break of at least 6 N, elongation of 400 per cent, a length of at least 240 mm and a size M weight tolerance of ±0.3 g. Those four numbers together describe a glove; the gram weight on its own does not.

Leaching: the stage buyers never ask about and always feel

Leaching runs twice — once on the wet film before curing, once after. It washes out water-soluble residues, and it is the first thing a line shortens when it is chasing output, because nothing about a shortened leach is visible at the packing table. It shows up later as odour in a freshly opened box, as skin irritation reports from a ward, and as a cytotoxicity result that was fine last year.

If you are comparing two offers at the same weight and the same test report, ask about leach tank count and line speed. In practice that is the single question that separates a line running for its own name from a line running for whoever called last week.

Chlorination or polymer coating: two ways to the same donning

Powder has not been an option in this industry since the US ban on powdered patient examination and surgeon’s gloves took effect on 18 January 2017, published at 81 FR 91722, and that ban applies whatever the glove material. What replaced powder is one of two finishes.

  • Chlorination treats the surface with chlorine, hardening it slightly so the glove releases from itself and from skin. It is the lower-cost route. Over-chlorination is a real defect: it yellows the glove, stiffens it and reduces tensile performance, and it is detectable by smell before any instrument finds it.
  • Polymer coating applies an inner coating instead. It gives softer donning and a more consistent feel, particularly on damp hands, at a higher cost per piece.

Which route each of our models uses is confirmed with the quotation rather than stated here, because the answer is model-specific and we would rather be held to a written answer than a web page.

Out-of-line inspection and the AQL question

Finished gloves are sampled under ISO 2859-1, general inspection level II, with the lot defined as the production batch. The pinhole test is the water leak method: a glove is filled with 1000 ml of water and held for the defined period, per ASTM D5151 and the equivalent European method. The standard’s own caveat is worth repeating to anyone who treats it as a guarantee of sterility of barrier — it detects only holes that leak water under the test conditions and does not establish the smallest detectable hole.

The acceptance number is set by destination market, and the two main markets do not agree: the US applies AQL 2.5 to patient examination gloves under 21 CFR 800.20, while the EU applies AQL 1.5 under EN 455-1. We run at AQL 1.5, which is the tighter of the two, so one line serves both. Alongside pinholes, each lot is checked for dimensions, weight tolerance, force at break and elongation, and the records stay with the batch.

Packing, traceability and what travels with the goods

Item Our standard
Count hierarchy 100 pieces per box, 10 boxes per carton, reconciled by piece rather than by box
Lot code Carried on the box and the carton so any complaint traces back to one production batch and its test records
Container planning Gloves are a cube commodity; as planning figures a 20ft box takes roughly 26–28 m³ of export cartons, a 40ft 55–58 m³ and a 40HQ 65–68 m³. Cartons per container come from the loading plan, not an estimate
Incoterm and port of loading We quote FOB, CIF or DDP as you prefer; the port of loading for a Guangdong plant is confirmed with the quotation rather than assumed
HS line 4015.12 for gloves of vulcanised rubber of a kind used for medical, surgical, dental or veterinary purposes; vinyl gloves sit on a different line. Confirm the duty against your own tariff before comparing a landed figure
Price basis Indicative USD per carton against the prevailing NBR index, with a validity window stated on the quotation. An open-ended price in this trade usually means there is room in the gram weight
MOQ, lead time and payment Our minimum order quantity is flexible — tell us the quantity you need and we quote accordingly. Lead time and payment terms are confirmed with each quotation

On documentation: for the United States, factory registration and device listing information is provided with the quotation. For the European Union, our gloves are CE marked under the applicable EU regulations and the EU declaration of conformity is provided with the quotation, naming the legal manufacturer and the EU authorised representative (EC REP) for that model. Tell us the destination market and we send the exact document set for that market and that model rather than a general pack.

Private label: which stages you can change

OEM and private label work touches four of the nine stages, and it is worth knowing which, because it tells you what is quick and what is not.

  • Compound (stage 1) — pigment for a colour change. A new colour needs a trial run and a shade approval, not just an instruction.
  • Dip (stages 3 and 4) — gram weight within the range the line runs.
  • Finish (stage 8) — chlorinated or coated, where the model allows it.
  • Packing (stage 9) — box artwork, carton markings, count per box where a size makes a different count sensible.

The lead time on private label is set by the printed box, not by the glove: print runs against a minimum per design and per colour set, so three language versions are three minimums. Buyers planning a multi-market launch on one order learn this at the artwork stage, usually after the glove specification is already closed. We arrange the artwork proof and the production sample before the main run so the shade and the print are both signed off against a physical item.

What we would ask for if we were buying

Four lines, in the order they move the number: the destination market, so the acceptance figure and the document set are fixed from the start; gram weight plus the measured thickness points with a tolerance band; the standards each lot must be tested to, with the edition named; and the size split as a percentage, because the heavy sizes carry more material at the same price per carton.

Related reading on our own specifications: the nitrile glove weight guide covers how gram weight is set and measured, AQL for examination gloves explains the sampling behind the acceptance figures above, and powder-free nitrile exam glove specifications sets out what replaced powder in detail. Product pages for the models discussed: HM-1101 nitrile gloves 3.5 g, HM-1303 nitrile gloves 6.0 g and MXGUARD nitrile exam gloves.

FAQ

How long does it take to make a nitrile glove from latex to packed carton?

The dipping line itself is a continuous process measured in minutes per former pass, but the order lead time that matters to you includes compounding and maturation, the run itself, out-of-line inspection, and printed packaging where private label is involved; we confirm the lead time with each quotation rather than quoting a standard number, because the printed box is usually the long pole rather than the glove.

How is the minimum order quantity set?

Our minimum order quantity is flexible — tell us the quantity, the weights and the size split you need and we will quote accordingly, and if the order is private label the practical floor is set by the print minimum on the box rather than by the gloves.

Can you make accelerator-free or specific-colour gloves?

Colour changes are handled in compounding with a trial run and a shade approval before the main production; for any other compound change, including accelerator-free systems, ask us against the specific model and we will answer in writing with what the line can hold, because this is a model-specific answer rather than a range-wide one.

What documents come with a shipment?

Invoice and packing list split by HS line, the lot test records covering pinhole, dimensional and physical property results for the batch shipped, the EU declaration of conformity for the European Union, and the US factory registration and device listing information — all provided with the quotation and the shipment for the destination market you tell us.

How do you handle a quality complaint after delivery?

Send the lot code from the box or carton with photographs and the affected quantity, and we trace it to the production batch and its test records; where a batch is confirmed out of specification we agree the remedy in writing against that batch rather than against the whole order.

WhatsApp